Lubuntu 15.04 GPU增强版含ARIA2 SAMBA minidlna vsftp蓝牙驱动等

jacer

Lubuntu 15.04 GPU增强版含ARIA2 SAMBA minidlna vsftp蓝牙驱动等
本镜像根据loboris的Lubuntu 15.04加最新内核3.4.39-02修改，默认支持Orange Pi PC,
Orange Pi Plus、Orange Pi Plus 2、Orange Pi 2、Orange Pi Mini需要替换FAT分区文件才
能使用所有USB和以太网，可以直接烧写启动。需要16GB TF卡，因为根据16GB TF卡备
份而来，无需扩展分区，有12GB可用空间。

支持SSH、1-wire、GPIO、SPI、UART
含GPU驱动，可以运行glmark2-es2跑分
含USB蓝牙驱动
支持插入耳机和音响到AV口外放
含ARIA2下载机 输入OPI的局域网IP\yaaw或者局域网IP\aria2进入Aria2管理界面
含samba服务 在局域网WINDOWS电脑映射网络磁盘输入 \\OPI的局域网IP\share 然后输入用户名orangepi和密码share可以读写插入到OPI的U盘上文件
含vsftpd服务 在FlashFXP等FTP工具中输入OPI的局域网IP连接后输入默认账号和密码orangepi进行FTP传输
含minidlna服务 可以将下载到OPI接的U盘的视频 音乐 图片推送到局域网的电视盒子 手机 平板等
含几款USB无线网卡驱动
含1个纸牌游戏
含1个1080P H264的test测试视频文件

下载地址如下 Lubuntu 15.04带GPU驱动月亮河修改版

这个镜像是为OPI-PC做的，OPI-PLUS、OPI-PLUS2也可以使用，OPI-2 OPI-MINI也没有问题，只需要运行下面命令然后选对开发板型号和显示器分辨率即可。

1. wget http://loboris.eu/update_kernel.sh
   
2. sudo mv update_kernel.sh /usr/local/bin
   
3. sudo chmod +x /usr/local/bin/update_kernel.sh
   
4. sudo update_kernel.sh test

复制代码

如果你的TF卡容量小于16GB，请使用下面链接的镜像，烧写后需要扩展分区使用sudo fs_resize命令，下面镜像使用内核为OPI-PLUS（2）的，如果你使用的为OPI-PC，请将烧写后的TF卡放入读卡器后插上WINDOWS电脑，将下面文件解压覆盖到挂载的磁盘分区里面即可，如果你的使用的PLUS或PLUS 2则无需该步骤。
缩小版镜像 需要扩展分区 内核为OPI-PLUS用 OPI-PC需要替换FAT文件

OPI-PC用的FAT替换文件

OPI-2和OPI-MINI用的FAT替换文件

无影

月亮做了这么好的镜像，为了造福大家，我把他的镜像从16G左右缩小到了2.5G，压缩文件缩小到700M，下载地址月亮河修改版--压缩缩小到700M，说明：只是缩小了IMG大小，其他未作改动，FAT分区已经拷入了loboris的最新内核uImage和script文件（跟以往的uImage不同，使用以往的uImage不能认到新内核），默认是plus，需要修改成其他板子的话直接修改FAT里面的文件即可，不需要运行update_kernel.sh test。

还有，第一次启动记得要运行 sudo fs_resize扩展卡空间，理论上可以刷入含4G以及以上容量的内存卡。

注意运行 uname -a 显示的应该是Linux OrangePI 3.4.39-02-lobo



中文版月亮河修改版--缩小--mate--中文--X2GO

ljq917181927

楼主，显示溢出屏幕边缘怎么办啊。修改script。bin可以吗。我用的是电视做显示器

cnorangepijeff

Is the HDMI audio problem resolved? The HDMI audio can't make sound in the other mirror img. Is this img same as the other one? Wait feedback.

cnorangepijeff

The download address is failed for downloading.

jacer

cnorangepijeff 发表于 2016-2-29 13:49
Is the HDMI audio problem resolved? The HDMI audio can't make sound in the other mirror img. Is this ...

Yes it is resolved.

jzopen

刚才烧录到64G TF卡，替换了PC的那些文件，启动时显示器黑屏，用串口跟踪，发现启动失败，输出如下：

HELLO! BOOT0 is starting!
boot0 version : 4.0.0
fel_flag = 0x00000000
rtc[0] value = 0x00000000
rtc[1] value = 0x00000000
rtc[2] value = 0x00000000
rtc[3] value = 0x00000000
rtc[4] value = 0x00000000
rtc[5] value = 0x00000000
rtc[6] value = 0x00000000
rtc[7] value = 0x00000000
DRAM DRIVE INFO: V0.8
DRAM Type = 3 (2DR2,3DR3,6PDDR2,7PDDR3)
DRAM CLK = 672 MHz
DRAM zq value: 003b3bfb
READ DQS LCDL = 001f1f1f
DRAM SIZE =1024 M
odt delay
dram size =1024
card boot number = 0
card no is 0
sdcard 0 line count 4
[mmc]: mmc driver ver 2014-12-10 21:20:39
[mmc]: ***Try SD card 0***
[mmc]: SD/MMC Card: 4bit, capacity: 64000MB
[mmc]: vendor: Man 00003000 Snr 12800007
[mmc]: product: APPSD
[mmc]: revision: 0.0
[mmc]: ***SD/MMC 0 init OK!!!***
sdcard 0 init ok
The size of uboot is 000dc000.
sum=ede66ee7
src_sum=ede66ee7
Succeed in loading uboot from sdmmc flash.
Ready to disable icache.
Jump to secend Boot.
SUNXI_NORMAL_MODE   
[      0.349]e mode

U-Boot 2011.09-rc1 (Jun 21 2015 - 19:33:17) Allwinner Technology

[      0.356]version: 1.1.0
normal mode
[      0.364]pmbus:   ready
not set main pmu id
axp_probe error
[      0.379]PMU: pll1 1200 Mhz,PLL6=600 Mhz
AXI=400 Mhz,AHB=200 Mhz, APB1=100 Mhz
sid read already
fel key new mode
run key detect
no key found
no key input
dram_para_set start
dram_para_set end
normal mode
[      0.409]DRAM:  1 GiB
relocation Offset is: 35af9000
[box standby] read rtc = 0x0
[box_start_os] mag be start_type no use
user_gpio config
user_gpio ok
gic: normal or no secure os mode
workmode = 0
MMC:     0
[      0.483][mmc]: mmc driver ver 2014-12-10 9:23:00
[      0.488][mmc]: get sdc_phy_wipe fail.
[      0.492][mmc]: get sdc0 sdc_erase fail.
[      0.496][mmc]: get sdc_f_max fail,use default 50000000Hz
[      0.501][mmc]: get sdc_ex_dly_used fail,use default dly
[      0.507][mmc]: SUNXI SD/MMC: 0
[      0.520][mmc]: *Try SD card 0*
[      0.555][mmc]: CID 0x300041 0x50505344 0x128000 0x7002a01
[      0.560][mmc]: mmc clk 25000000
[      0.563][mmc]: SD/MMC Card: 4bit, capacity: 64000MB
[      0.568][mmc]: boot0 capacity: 0KB,boot1 capacity: 0KB
[      0.573][mmc]: ***SD/MMC 0 init OK!!!***
[      0.578][mmc]: erase_grp_size:0x1WrBlk * 0x200 = 0x200 Byte
[      0.583][mmc]: secure_feature 0x0
[      0.587][mmc]: secure_removal_type  0x0
[      0.591]sunxi flash init ok
script config pll_de to 864 Mhz
Not Found clk pll_video1 in script
script config pll_video to 297 Mhz
[boot]disp_init_tv
[DISP_TV] disp_init_tv enter g_tv_used
screen 0 do not support TV TYPE!
[BOOOT_DISP_TV] disp tv device_registered
unable to find regulator vcc-hdmi-18 from [pmu1_regu] or [pmu2_regu]
enable power vcc-hdmi-18, ret=-1
DRV_DISP_Init end
boot_disp.auto_hpd=1
auto hpd check has 50 times!
[disk_read_fs] no the partition
error: open disp_rsl.fex, maybe it is not exist
attched ok, mgr1<-->device1, type=2, mode=11----
ready to set mode
disp_tv_enable
[      1.432]finally, output_type=0x2, output_mode=0xb, screen_id=0x1, disp_para=0x20b0000
fail to find part named env
Using default environment

In:    serial
Out:   serial
Err:   serial
--------fastboot partitions--------
mbr not exist
base bootcmd=run setargs_mmc boot_normal
bootcmd set setargs_mmc
key 0
cant find rcvy value
cant find fstbt value
no misc partition is found
to be run cmd=run setargs_mmc boot_normal
[      1.469][mmc]: MMC Device 2 not found
[      1.473][mmc]: Can not find mmc dev
[      1.477][mmc]: read first backup failed in fun sdmmc_secure_storage_read line 1849
sunxi_secstorage_read fail
get secure storage map err
the private part isn't exist
WORK_MODE_BOOT
adver not need show
sunxi_bmp_logo_display
[disk_read_fs] no the partition
error: open bootlogo.bmp, maybe it is not exist
sunxi bmp info error : unable to open logo file bootlogo.bmp
[      1.510]Hit any key to stop autoboot:  0
[      4.770][mmc]: blkcnt should not be 0
[      5.811][mmc]: blkcnt should not be 0
## Booting kernel from Legacy Image at 40007800 ...
   Image Name:   Linux-3.4.39-02-lobo
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    10967120 Bytes = 10.5 MiB
   Load Address: 40008000
   Entry Point:  40008000
   Verifying Checksum ... Bad Data CRC
ERROR: can't get kernel image!
sunxi#ls
Unknown command 'ls' - try 'help'
sunxi#